Angel Care AC401 Owner's Manual download pdf (Page 6)

20) Antenna -The antenna used for this transmitter

must be installed to provide a separation distance of

at least 20 cm (7.9”) from all persons and must not

be collocated or operating in conjunction with any

other antenna or transmitter.

21) Power Lines- An outside antenna system should

NOT be located in the vicinity of overhead power

lines or other electric light or power circuit, or where

it can fall into such power lines or circuits as contact

with them may be fatal.

22) STRANGULATION HAZARD. Children have

STRANGLED in cords. Keep the adapter cords and

sensor pad cord out of the reach of children.

Because of the serious strangulation risk to infants

and toddlers, parents and caregivers should NEVER

place the nursery unit within 3 feet (1 meter) of a

crib. NEVER use extension cords with AC adapters.

ONLY use the AC adapters provided.

23) Interference- This monitor uses public airwaves

to transmit signals. The Parent Unit may pick up

signals or interference from other nursery monitors

in your area. Your monitor may even be picked up by

other households. To protect your privacy, make

sure both units are turned off when not in use. If you

experience interference, change the channel on

both units.

24) Vibration Source- When the monitor is in use, do

NOT use a crib mobile or other crib accessories that

may produce vibrations. Other sources of vibrations

may include fans, washing machines, loud music,

etc. These sources of vibration may interfere with

the performance of your Angelcare® monitor and

the alarm will not sound if it continues to detect any

movement other than your baby’s. Be sure all

vibration sources are eliminated before using the

monitor.

You may experience false alarms for several

reasons. The most common reason is the Nursery

Unit has not been turned off after you have removed

your baby from the crib. Another reason is the

Sensor Pad has not been placed under the mattress

properly.

Be sure the Sensor Pad is on a flat, firm surface with

the printed side facing up. The sensitivity level may

also need to be adjusted. Refer to the Movement

Sensitivity Adjustment section on P 9. Always be

sure to immediately check on baby whenever an

alarm sounds.

25) Sensor Pad- Your sensor pad can be used in

any crib that is stationary and designed to safely

hold a baby. If the crib has a spring or slat base,

place a hard board between the crib base and the

Sensor Pad measuring at least 13” x 13” (33 x 33

cm) and 1/4 inch (6 mm) thick. Only use your

Angelcare® monitor in a stationary sleeping

environment such as a crib where the Sensor Pad

can rest on a completely flat, firm surface.

ALWAYS route the sensor pad cord below crib

mattress ONLY and out of reach of children.

IMPORTANT SAFETY INSTRUCTIONS

RELATED TO USE OF BATTERIES

1) Use ONLY the type and size of batteries specified

in the user manual. There is a risk of explosion if

batteries are replaced with an incorrect type.

2) Use ONLY AAA (LR03) rechargeable batteries

and/or the AC adapters provided for the Parent

Units. You must use only rechargeable batteries in

the Parent Unit. DO NOT use alkaline batteries or

you will severely damage the unit.

3) Charge the batteries for 15 hours prior to first use.

Be sure to have the monitor in the OFF position

during this period. ONLY use the AC adapters

included with your monitor.

4) Do NOT use these adapters with any other

equipments.

5) When unplugging the AC adapter from the

nursery unit, be sure it is switched to the off position.

If it isn’t, the unit will revert to battery mode if

batteries are installed.

6) Do NOT use rechargeable batteries in the

Nursery Unit.

AC401 NA 13 12 2012_AC401inter 042008 12-12-19 8:48 AM Page 6

1 2 3 4 5 6 7 8 9 10 11 ... 49 50

Comments to this Manuals

No comments

Angel Care AC401 Owner's Manual Page 6

Comments to this Manuals