Angel Care AC401 Owner's Manual download pdf (Page 14)

Note: Test your Angelcare® monitor BEFORE using it for the first time and then on a regular basis to make sure that it is functioning properly.The

Angelcare® monitor can be used outside of the crib in a different sleeping area.Test your monitor when moving the sensor pad to a new location

to ensure sensitivity is adjusted correctly to the new padding or mattress. Consult the movement sensitivity adjustment section (step 6).

1.TEST THE SOUND Switch the Parent Unit to the “Sound Only”function. Have someone else speak into the nursery unit or place a radio near the

nursery unit. You should hear sound from the Parent Unit. If there is no sound,refer to the Troubleshooting section.

2.TEST YOUR MONITOR TO DETECT MOVEMENT Make sure the sensor pad's cord is plugged into the nursery unit then turn both units ON. Set

the Parent Unit on the“Movement only” function. Gently move your hand on the mattress.The top green light (with pendulum symbol) will flash

on the nursery unit with your every movement. Remove your hand from the mattress. Due to the lack of movement, a “pre-alarm “Tic”sound will

be emitted after 15 seconds and 5 seconds later, the alarm will sound and the green lighton the nursery unit will turn off.

3. TEST THE STOPPING OF THE ALARM To stop the alarm, place your hand lightly on the mattress so that the sensor pad starts detecting

movement again.The green light with the pendulum icon will start flashing again, as movement is detected by the sensor pad. You may also shut

the nursery unit OFF and turn it ON again to stop the alarm.

NOTE: If the alarm does not sound, the sensor pad may be detecting a continuous vibration from the floor, a strong draft or the crib is being

touched. Avoid contact with crib when monitor is in use. Place crib near a solid supporting wall and away from strong air currents. The sensitivity

of the sensor pad may need to be reduced,consult the movement sensitivity adjustment STEP 2.

4.VERIFYING THE BATTERY MODE Verify that the battery mode is functional by operating both units without the AC adapters. If the green light on

the nursery unit does not light up, the batteries need to be replaced. If the Parent Unit doesn’t light up and the screen does not appear, it needs

to be recharged.

STEP 12

ADDITIONAL FUNCTIONS

• CHANNEL SELECTION:

If the transmission is not clear, or if you hear parasite sounds, you should change the

channel. Press and hold the SELECT button to change the channel (with the arrows). Then

press the SELECT button again to confirm.

• TEMPORARY MUTE:

If you want to mute the sound for 2 minutes, press the center EXIT button. To reactivate the

sound before the 2 minutes have elapsed, press EXIT again. You can also turn the alarm off

by pressing the same button (this does not apply to the low battery alarm).

• HOLD:

Press and hold the down volume arrow for 2 second. This symbol “H” will apear on the

Parent Unit display. This function allows you to put the monitor on Hold when you need to

pick the baby out of the crib for a short period of time. During this period, the movement

alarm will not go off, nor the sound will be transmitted. A double beep will be heard every

minute to let you know the monitor is on Hold. To void this function, press and hold the down

volume arrow for 2 second. The display will revert to normal.

Note: When there is a movement alarm, press any key to put the monitor on HOLD. During

SOUND ONLY mode, the HOLD function is not active.

•CONNECTING THE PARENT UNIT TO THE NURSERY UNIT:

If you lose the connection between the 2 units,turn them both off. Turn ON the Parent Unit and

press and hold the MENU button ,the "out of range"indicator will flash and you will hear a

beep.Turn ON the nursery unit and press and hold the top button of the nursery unit to re-

connect.The Tic light flashes.This normally happens within a few seconds and you will hear a bleep

to confirm it. If successful, the Parent Unit display will first show the channel of transmission (C1

to C8), which will be replaced by the room temperature and icons for all activated functions.

Note : The connecting process should be done within 30 seconds. If longer, the operation will be

ignored and you will have to start over.

• PAGING:

If you want to locate the Parent Unit, press the top button of the nursery unit.

Low battery indicator

• The monitor will revert to battery mode during a power failure only if batteries are inserted

in both units.

• When the nursery unit’s low battery RED light is flashing, its batteries need to be replaced.

On the screen of the Parent Unit, the battery icon flashes and the nursery unit icon appears.

A short BEEP will also be heard every 15 seconds for about 30 minutes, until the unit shuts

itself off.

• Parent Unit should be recharged when icon is clear (will not flash) and a beep sound is

heard. A short BEEP sound will be heard every 15 seconds until the unit shuts itself down.

Note: Do not use Alkaline batteries in the Parent Unit.

IMPORTANT : If the “Out of range” function is ON, when the nursery unit shuts itself off, the

“Out of range” signal will be heard and displayed on the Parent Unit.

Low battery

indicator

Red light

STEP 11

BATTERY MODE AND WARNINGS

STEP 13

ADDITIONAL FUNCTIONS

TESTING YOUR ANGELCARE

MONITOR

AC401 NA 13 12 2012_AC401inter 042008 12-12-19 8:48 AM Page 14

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 49 50

Comments to this Manuals

No comments

Angel Care AC401 Owner's Manual Page 14

Comments to this Manuals